Схема SRS AirBag Toyota HIACE [Америка] 2005 год
Airbag Sensor (Front LH)
Combination Meter
Airbag Squib (Front Passenger's Airbag Assembly)
Airbag Squib (Steering Wheel Pad)
Airbag Sensor (Front RH)
Airbag Sensor Assembly Center
Engine ECU
Junction Connector
Front Seat Outer Belt (LH) , Front Seat Outer Belt (RH)
DLC3
Front Seat Outer Belt (LH) , Front Seat Outer Belt (RH)
PD+
PD-
Y
PP+
PP-
1
Y-B
B
Y
Y-B
Y
Y-R
Y-G
Y-G
Y-R
Y
Y-B
2
1
15A IGN
(*8)
(*8)
2
1
5E
16
6
1
IG2
1
10A MET IGN
5M
1
LA
A
2
D+
5S
14
5E
32
4
SRS
B-O
D-
B-R
B-Y
B-O
B-Y
P-
B-Y
H20
GSW2
5
6
5E
8
5E
15
L
L
2
TC
A
40
P-B
SIL
P+
W-B
W
3
Spiral Cable
(IG)
(IG)
* 1 :w/ Front Passenger's Airbag
P-
D-
D+
P+
IG+
SW
5M
7
4
A
21
A
A
14
A
22
A
15
A
16
A
3
A
30
A
28
A
29
A
27
B
2
B
1
C
(*1)
(*1)
(*1)
(*1)
(*1)
(*1)
(*1)
6C
17
6C
18
W
(*2)
W
(*2)
(*3)
* 2 :w/ Engine Immobiliser System
* 3 :w/o Engine Immobiliser System
2
2
4
4
1
1
(*7)
(*6)
3
3
* 6 :LHD, RHD Before Aug. 2010 Production
* 7 :RHD From Aug. 2010 Production
1
12
* 8 :1TR-FE, 2TR-FE
* If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section of the Repair Manual.
* After work on the SRS is completed, check the SRS warning light.
* Information labels are attached to the periphery of the SRS components. Follow the instructions of the notice.
* Use a volt/ohmmeter with high impedance (10 kΩ/V minimum) for troubleshooting electrical circuits of the system.
* If the following parts have been dropped, or have cracks, dents and other defects in their case, bracket, and connector replace with new one.
* For the purpose of reuse, never disassemble and repair the following parts.
4
C
5
A
25
A
26
B
1
A
1
(RHD)
B
2
(LHD)
A
2
5H
4
5E
13
5S
3
5E
31
W-B
B4(A),B5(B),B6(C)
P-B
W
SIL
TC
F/PS
13
7
H23
B7(B)
B
32
Airbag Sensor (Front RH)
Airbag Sensor (Front LH)
Airbag Sensor Assembly Center
Airbag Sensor Assembly Center
Engine ECU
Front Seat Outer Belt (LH)
Front Seat Outer Belt (LH)
Front Seat Outer Belt (RH)
Front Seat Outer Belt (RH)
Combination Meter
DLC3
Airbag Squib (Steering Wheel Pad)
Junction Connector
Airbag Squib (Front Passenger's Airbag Assembly)
Pretensioner
Pretensioner
(*1)
30
5E
W-B
W-B
5E
12
5E
14
E2
E1
2
A
(LHD)
B23(B)
B25(A)
B25(B)
L+(LHD) R+(RHD)
L-(LHD) R-(RHD)
R+(LHD) L+(RHD)
R-(LHD) L-(RHD)
B23(A)
+SL
-SL
Y-B
2
B
A12
W-R
BR
A13
-SL
-SR
+SR
+SL
BR
2
1
1
(RHD)
2
J1
Y-B
W-R
H32
Y
B4(A),B5(B),B6(C)
W-B
+SR
H41
-SR
B-W
BR-W
BR-W
B-W
1
A
* Never use SRS parts from another vehicle. When replacing parts, replace with new parts.
* Even in cases of a minor collision where the SRS does not deploy, the following parts should be inspected;
* Do not expose the following parts directly to hot air or flame;
* Before repair, remove the airbag sensor if shocks are likely to be applied to the sensor during repair.
* Steering wheel pad
* Front passenger airbag assembly
* Seat belt pretensioner
* Center airbag sensor assembly
* Front airbag sensor assembly
* Work must be started more than 90 seconds after the ignition SW is turned to the "LOCK" position and the negative (-) terminal cable is disconnected from the battery. (The SRS is equipped with a back-up power source so that if work is started within 90 seconds from disconnecting the negative (-) terminal cable of the battery, the SRS may deploy.)
* Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most important source of information when troubleshooting. When troubleshooting the SRS, always inspect the DTCs before disconnecting the battery.
NOTICE :When inspecting or repairing the SRS, perform service in accordance with the following precautionary instructions and the procedure, and precautions in the Repair Manual applicable for the model year.
* When the negative (-) terminal cable is disconnected from the battery, the memory of the clock and audio system will be cleared. So before starting work, make a record of the contents in the audio memory system. When work is finished, reset the audio systems as they were before and adjust the clock. Some vehicles have power tilt steering, power telescopic steering, power seat and power outside rear view mirror which are all equipped with memory function. However, it is not possible to make a record of these memory contents. So when the work is finished, it will be necessary to explain it to your customer, and ask the customer to adjust the features and reset the memory. To avoid erasing the memory in each system, never use a back-up power supply from outside the vehicle.
HJ1
HB3
AB2
HJ1
HB3
HB3
HB3
AB3
AB2
AB3
AB2
AB3
AB2
AB3
H1
B3
Электрические цепи подушек безопасности защищены предохранителем IGN на 10 Ампер (красный) , Машины с двигателями 1TR-FE 2TR-FE.. На этом автомобиле система SRS AirBag не имеет коммуникации по CAN-BUS.
В данной схеме рассмотрены модификации: