Toyota
Lexus
Scion

Схема SRS AirBag Toyota HIGHLANDER HV [Америка] 2007 год

Occupant Detection ECU Lower No.1 Instrument Panel Airbag Assembly Junction Connector Front Pretensioner LH Junction Connector Hybrid Vehicle Control ECU Junction Connector Front Pretensioner RH With Multi Information Display Clock Assembly Front Out Weight Detection Sensor Sub Assembly Side Airbag Squib Circuit LH Front In Weight Detection Sensor Sub Assembly Curtain Shield Airbag Assembly RH Side Airbag Squib Circuit RH Junction Connector Integration Control and Panel Assembly Center Airbag Sensor Assembly DLC3 Curtain Shield Airbag Assembly LH Front Airbag Sensor RH Junction Connector Front Side Airbag Sensor Assembly LH Front Airbag Sensor LH Front Side Airbag Sensor Assembly RH Front Passenger Side Squib Circuit Junction Connector Rear In Weight Detection Sensor Sub Assembly Front Seat Inner Belt Assembly LH Spiral Cable Sub-Assembly , Driver Side Squib Circuit , Driver Side Squib 2nd Step Circuit Combination Meter Rear Out Weight Detection Sensor Sub Assembly Rear Side Airbag Sensor Assembly RH Driver Side Squib 2nd Step Circuit , Spiral Cable Sub-Assembly Junction Connector Rear Side Airbag Sensor Assembly LH Driver Side Squib Circuit , Spiral Cable Sub-Assembly Junction Connector Front Seat Inner Belt Assembly RH Main Body ECU Junction Connector D53(A), E24(B) 7 Junction Connector B B GR P B DIA 26 A W 7 2 2 SIL W 1G 22 A 15 B W-B A 3 A 4 A 2 W-B P- 2 1 2 Driver Side Squib Circuit z3(B) 25 2 BR O W W SB O GR W G LG E23 Junction Connector 12 10 1L 13 1D B 1 2 11 W-B Buckle Switch Buckle Switch W-B 3 AIRBAG ON/OFF Indicator 13 12 2 2 1 3 2 3 1 1 1 2 2 3 1 3 Y-B Y Y-R Y-G 4 3 2 1 1 A 2 A 1 B 2 B ICL+ Front Seat Inner Belt Assembly RH Rear Out Weight Detection Sensor Sub Assembly Front Out Weight Detection Sensor Sub Assembly Rear In Weight Detection Sensor Sub Assembly Front In Weight Detection Sensor Sub Assembly Rear Side Airbag Sensor Assembly RH Front Pretensioner RH Front Side Airbag Sensor Assembly RH Occupant Detection ECU Side Airbag Squib Circuit RH Curtain Shield Airbag Assembly RH Front Pretensioner LH Front Side Airbag Sensor Assembly LH Front Seat Inner Belt Assembly LH Curtain Shield Airbag Assembly LH Side Airbag Squib Circuit LH Rear Side Airbag Sensor Assembly LH Integration Control and Panel Assembly Combination Meter Lower No. 1 Instrument Panel Airbag Assembly Front Passenger Side Squib Circuit Center Airbag Sensor Assembly Center Airbag Sensor Assembly 1 Front Airbag Sensor RH Front Airbag Sensor LH E1 Junction Connector E23 R W 21 (IG) Drive IC IG2 CANH ES CANL Micro Computer B B2 B SRS IG+ 1 2 10A DOME (BAT) 5 22 20 21 22 CAN I/F 40 W-B 1 B 2 B 1 z4(C) Driver Side Squib 2nd Step Circuit 1D 10 1F 1 10 7. 5A GAUGE NO. 2 1G 12 3 Power Supply Circuit 2 (BAT) 10A ECU-B 2 E19 PAON P-AB 8 G R 4 6 W 1 R L R 3 4 16 L B ICR+ P2- R- L- R+ L+ 1 2 2 1 C ICL- IG B +B 6 (IG) 1E 9 BR B (BAT) 2 2 1D 10 1F 1 R W a5 W B BR R W R P L W 10A IGN 10A ECU-B 16 24 21 B B 5 3 B 9 LSP- O7 N6 N9 W-B 4 10 6 3 9 5 2 8 12 1 7 11 10 18 9 17 GR Y LG V Y G W B D30(A), N1(B), O1(C) a1(A), a3(B) a7 a9 a10 SGD4 SIG4 SVC4 SGD2 SIG2 SVC2 SGD1 SIG1 SVC3 4 2 3 1 A SGD2 A SIG2 SGD4 A SGD3 A SIG3 A DSP- C BR SVC1 SIG4 Seat Position Airbag Sensor SGD3 SIG3 SVC3 W L O G P R O10 B A SVC1 SIG1 A SVC4 A A A a8 LBE- DBE+ C A SGD1 SVC2 A C DBE- DSP+ C LSP+ 9 B 7 B 5 1M 1 14 FSR- FSR+ B BSW LBE+ W-B W B A IG2 8 B FSP- B FSP+ 4 26 25 18 17 23 24 27 29 28 30 5 6 8 7 4 3 1 2 9 10 5 6 4 1M 3 1 2 6 17 23 O3 N3 D2+ 5 W-B B B G R W B B R Y B Y G Y G B W R P+ Y-B Y R G Y Y-B Y Y-B Y Y-B Y-B Y D30(A), N1(B), O1(C) N4 O4 D29 e1(A), e2(B) A N5 R 10 1F 5 1E 3 1E 3 1G 6 1E 10 1H 2 1 2 1 BBL+ BBL- BBR+ BBR- BCR- BCR+ BCL- BCL+ -SR +SR DK- DK+ 2 1 2 1 3 4 3 1 2 1 2 1 2 1 2 10 P2+ C 1 2 1 2 1 2 1 B BBP- B BBP+ C P2- A P2+ A P- A P+ A D2- A D2+ A D- A D+ A BBD- B +SL B ICP+ B ICD- C ICD+ PP- B PP+ B 7 PD- C 4 PD+ C DK- A DK+ A 3 O12 G 8 C SFD+ SFD- 4 A33 G R BCR- BCR+ E1 A A O5 Y-B Y C B SFP+ SFP- B -SL ICP- A4 P-AB PAON A G Spiral Cable Y Y-B Y Y-B BCL- BCL+ A E2 A +SL -SL A A +SR -SR A C BR C BBD+ 1E 1 1M 3 B ICR- D- 2 D2- D+ GND BGND W W B W B 2 3 W D59 Junction Connector 2 15 4 7 B W W W F 25 B F 33 12 5 6 12 W 3 16 14 1 W CANL CANH 17 W B B 1 B CANH 6 14 W CANL W W W B W B W B SIL R DLC3 R R D58 Junction Connector R 3 1F 1 1H GR 6 7 D47 W 10 1E R Spiral Cable Sub-Assembly D15(A), z3(B), z4(C) W 13 22 B W CANH A A CANL W E2 Master Drive IC +B(DOME) or IG G SB L R R L Y SB G G SB L R Y Note : Please refer to the Multiplex Communication System - CAN section for information regarding the shielded communication lines. G HSI+ With Multi Information Display Clock Assembly SB B 14 A 22 11 Junction Connector P W GR W W-B D53(A), E24(B) W-B L R 2 1D 10 1F 1 10A ECU-B 2 (BAT) 14 7. 5A GAUGE NO. 2 12 1G (IG) +B IG E11 Y 10 SYNC DATA CLK 11 10 9 6 1 Y GND 5 20 21 8 B 12 3 HSI- Junction Connector E23 16 SGND BR 3 1M 1 E23 3 Junction Connector 10 1G W-B G Y MDAT 17 16 38 36 37 W LCL- LCL+ SYNC MCLK C SFL+ SFL- SFR+ SFR- Note : Please refer to the Multiplex Communication System - CAN section for information regarding the shielded communication lines. W-B BR BR 14 A SB GSW2 BR 8 E ABFS RBE+ RBE- Junction Connector D55 D9(C) Main Body ECU CANL CANH W B D35(E), D36(F) Hybrid Vehicle Control ECU 6 BR C BR 5 Note : Please refer to the Multiplex Communication System - CAN section for information regarding the shielded communication lines. 4 19 8 Buzzer * If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section of the Repair Manual. * After work on the SRS is completed, check the SRS warning light. * Information labels are attached to the periphery of the SRS components. Follow the instructions of the notice. * Use a volt/ohmmeter with high impedance (10 kΩ/V minimum) for troubleshooting electrical circuits of the system. * If the following parts have been dropped, or have cracks, dents and other defects in their case, bracket, and connector replace with new one. * For the purpose of reuse, never disassemble and repair the following parts. * Never use SRS parts from another vehicle. When replacing parts, replace with new parts. * Even in cases of a minor collision where the SRS does not deploy, the following parts should be inspected; * Do not expose the following parts directly to hot air or flame; * Before repair, remove the airbag sensor if shocks are likely to be applied to the sensor during repair. * Steering wheel pad * Side airbag assembly * Front passenger airbag assembly * Curtain shield airbag assembly * Seat belt pretensioner * Center airbag sensor assembly * Front airbag sensor assembly * Work must be started more than 90 seconds after the Power SW is pushed to the "OFF" position and the negative (-) terminal cable is disconnected from the battery. (The SRS is equipped with a back-up power source so that if work is started within 90 seconds from disconnecting the negative (-) terminal cable of the battery, the SRS may deploy. ) * Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most important source of information when troubleshooting. When troubleshooting the SRS, always inspect the DTCs before disconnecting the battery. * Rear airbag sensor assembly NOTICE : When inspecting or repairing the SRS, perform service in accordance with the following precautionary instructions and the procedure, and precautions in the Repair Manual applicable for the model year. * Side airbag sensor assembly * When the negative (-) terminal cable is disconnected from the battery, the memory of the clock and audio system will be cleared. So before starting work, make a record of the contents in the audio memory system. When work is finished, reset the audio systems as they were before and adjust the clock. Some vehicles have power tilt steering, power telescopic steering, power seat and power outside rear view mirror which are all equipped with memory function. However, it is not possible to make a record of these memory contents. So when the work is finished, it will be necessary to explain it to your customer, and ask the customer to adjust the features and reset the memory. To avoid erasing the memory in each system, never use a back-up power supply from outside the vehicle. * Knee airbag assembly DN3 Na1 ED1 ED3 De1 De1 Na1 De1 Na1 AD1 DN3 DN3 ED5 ED5 Na1 Na1 ED3 De1 DD1 ED3 ED3 ED1 ED1 DD1 DD1 AD6 AD6 AD1 Na1 D1 N1 D4 D3 E1 D3 E1 D3

Электрические цепи подушек безопасности защищены предохранителем IG2 на 10 Ампер (красный). На этом автомобиле система SRS AirBag имеет коммуникацию по CAN-BUS. Для устранения ошибки B1150/B1650 по системе классификации пассажира на эту машину можно установить эмулятор OPS-Lexus.

В данной схеме рассмотрены модификации: